无人平台复杂地形探测的视触融合方法

为提高无人平台在复杂环境中的地形探测能力以及解决在小样本数据下识别地形困难的问题，提出了一种无人平台复杂地形探测的视触融合方法。在原始宽度学习的基础上，建立了多模态级联特征节点宽度学习框架。首先进行触觉和视觉初步特征提取和融合特征提取，随后将融合特征矩阵经宽度学习分类器得到地形识别的结果。最后，在自建的视觉-触觉地形 (V-T2)数据集进行了实验验证。结果表明，相比于传统的融合算法，提出的融合算法有很好的准确性和鲁棒性，为无人平台地形探测提供了有效的策略。     

星载激光通信终端在轨机动对温度影响

对激光通信终端在轨瞬态温度变化开展了仿真，以期研究在轨机动的影响、热分析和热试验时机动模式的简化模拟。通过合理地分析与简化，建立终端的轨道热分析模型，准确模拟在轨机动，根据典型机动模式、外热流和涂层退化等因素设计了计算工况，得出了终端在轨运行过程中的温度场随时间和姿态变化规律。结果表明：不同机动模式下的温度变化存在差异，最大可达23.0℃，采用固定姿态或一维转动的简化热分析或热试验不能准确模拟实际飞行温度，甚至不能部分替代二维转动热分析或热试验；光学天线和反射镜的温度控制是制约终端工作的瓶颈，为终端设计合适的避光机动策略，可大幅度提高温度稳定度和均匀度。研究结果可以为光机电设备在轨机动策略的设计和改进提供参考。     

Modelling ignition probability with pairwise mixing-reaction model for flame particle tracking

Reduced order models for ignition analysis can offer insights into ignition processes and facilitate the combustor optimization. In this study, a Pairwise Mixing-Reaction (PMR) model is formulated to model the interaction between the flame particle and the surrounding cell mixture during Lagrangian flame particle tracking. Specifically, the model accounts for the two-way coupling of mass and energy between the flame particle and the surrounding shell layer by modelling the corresponding turbulent mixing, chemical reaction and evaporation process if present. The state of a flame particle, e.g., burnt, hot gas or extinguished, is determined based on particle temperature. This model can properly describe the ignition process with a spark kernel being initiated in a nonflammable region, which is of practical importance in certain turbine engines and has not been rigorously accounted for by the existing models based on the estimation of local Karlovitz number. The model is integrated into an ignition probability analysis platform and is demonstrated for a methane/air bluff-body flame with the flow and fuel/air mixing characteristics being extracted from a non-reacting simulation. The results show that for the spark location being at the extreme fuel-lean outer shear layer of the recirculation zone, PMR can yield ignition events with a significant number of active flame particles. The mechanisms for the survival of the initial flame particles and the entrainment of the survived flame particles into the recirculation zone are analyzed. The results also show that the ignition probability map from PMR agrees well with the experimental observation: a high ignition probability in the shear layer of the recirculation zone near the mean stoichiometric surface, and low ignition probabilities inside the recirculation zone and the top stagnation region of the recirculation zone. The parametric study shows that the predicted shape of the ignition progress factor and ignition probability is in general insensitive to the model parameters and the model is adequate for quantifying the regions with high ignition probabilities.     

A progressive approach to predict shot peening process parameters for forming integral panel of Al7050-T7451

In this paper, a progressive approach to predict the multiple shot peening process parameters for complex integral panel is proposed. Firstly, the invariable parameters in the forming process including shot size, mass flow, peening distance and peening angle are determined according to the empirical and machine type. Then, the optimal value of air pressure for the whole shot peening is selected by the experimental data. Finally, the feeding speed for every shot peening path is predicted by regression equation. The integral panel part with thickness from 2 mm to 5 mm and curvature radius from 3200 mm to 16000 mm is taken as a research object, and four experiments are conducted. In order to design specimens for acquiring the forming data, one experiment is conducted to compare the curvature radius of the plate and stringer-structural specimens, which were peened along the middle of the two stringers. The most striking finding of this experiment is that the outer shape error range is below 3.9%, so the plate specimens can be used in predicting feeding speed of the integral panel. The second experiment is performed and results show that when the coverage reaches the limit of 80%, the minimum feeding speed is 50 mm/s. By this feeding speed, the forming curvature radius of the specimens with different thickness from the third experiment is measured and compared with the research object, and the optimal air pressure is 0.15 MPa. Then, the plate specimens with thickness from 2 mm to 5 mm are peened in the fourth experiment, and the measured curvature radius data are used to calculate the feeding speed of different shot peening path by regressive analysis method. The algorithm is validated by forming a test part and the average deviation is 0.496 mm. It is shown that the approach can realize the forming of the integral panel precisely.     

基于AFI混合聚类算法的轴承故障诊断方法

针对滚动轴承振动信号标记数据量小、故障模式多样的现状，提出了一种基于AFI混合聚类算法的半监督式轴承振动信号故障诊断方法。利用小波包分解方法提取了信号的能量特征谱，并通过主成分分析方法增强了信号的特征；参考迭代自组织数据分析的“分裂”和“合并”的思想，为人工鱼群算法中的个体鱼增加了“分裂进化”和“合并进化”行为；采用模糊C均值方法定义了隶属度矩阵和目标函数，并利用改进的人工鱼群算法，迭代搜寻了目标函数的全局最优解，得到了各故障模式的聚类中心；通过计算测试数据的最近邻聚类中心，实现了故障模式识别。结果表明，该方法无需指定聚类簇数，能在标记数据量小的情况下完成训练，较同类方法表现出了更优的故障模式识别性能。     

非恒定增压式微尺度拉瓦尔喷管流动特性

针对微尺度喷流在航天器运动状态切换时出现的非恒定增压变化,采用直接模拟蒙特卡洛(DSMC)方法对阶跃式增压和线性式增压两种模式下的微尺度拉瓦尔喷管流场进行了模拟,并对其变化过程中的流动特性进行了对比分析。结果显示：阶跃式增压会导致流动特性出现较大幅值的峰谷式波动,而线性式增压下的流动特性则呈现出线性变化的特点;黏性力对微尺度喷流的非恒定增压变化产生了重要的黏滞作用,在喉部扩张段至出口的流场中尤为明显;在设定的条件下,阶跃式增压过程中喷流产生的总冲量较线性式增压高59.5%,质量流量高74.7%,单位工质提供的冲量低约8.6%,波动性也高于线性式模型,阶跃式增压适用于系统需要较大推力改变运动状态且推进剂充足的情况,而线性式增压在系统精确微调或需要推进剂产生更高效能时具有明显的优势。     

扑旋翼飞行器气动特性分析及机翼拓扑优化设计

建立微型扑旋翼飞行器运动学模型,基于面元法研究低雷诺数下非定常场中扑旋翼飞行器的气动特性,得到机翼气动特性和一个工作周期内的最大气动载荷。建立扑旋翼飞行器机翼有限元模型,基于变密度法和独立连续映射法(Independent continuous mapping,ICM)对机翼进行静力学和动力学拓扑优化设计,通过改变机翼拓扑结构优化机翼模态频率,得到同时满足结构静力学和动力学要求的扑旋翼飞行器机翼拓扑结构。本文为扑旋翼飞行器机翼结构优化设计提供了基本思路和研究基础。     

一种柔性空间双臂机器人的协同控制和避障方法

针对柔性空间机械臂在轨服务应用需求，提出一种基于刚体运动与柔性振动相耦合的空间双臂机器人协同控制方法.首先引入空间位姿变量的概念，构造出面向协同控制目标的Jacobian矩阵，建立柔性空间机器人系统的刚柔耦合动力学模型，基于指定的最小距离得到其运动学逆解，并根据系统动量矩守恒关系及系统的Jacobian矩阵，并根据机械臂末端的运动速度,然后采用阻尼最小二乘法得出关节角度，使柔性空间机器人能够有效完成协同控制和空间避障任务，并基于RecurDyn V7R5软件环境验证算法的正确性.最后，基于SolidWorks和ADAMS虚拟样机建立柔性空间机器人系统的立体CAD模型，并结合空间在轨搬运任务进行模拟仿真，柔性空间机器人关节操作和运动轨迹的仿真结果图验证了本文算法的有效性.     

面向空间天线的TWF复合材料性能研究

利用碳纤维三向编织物（triaxial woven fabric，TWF）作为增强材料，与柔性基体材料硅橡胶复合，制成兼具一定柔性和刚性的复合材料壳膜结构，用于卫星天线反射器，是一种新型的高精度可展开天线实现方案。采用复合材料细观方法，对碳纤维增强硅橡胶TWF复合材料进行了力学性能的研究。首先由纤维和基体的材料特性得到均质纤维束的材料特性；接下来考虑纤维束交织情况（起伏波动）建立由纤维束组成的单胞实体有限元模型；然后对单胞实体有限元模型进行均匀化分析，施加周期性边界条件，最终得到等效的均质材料特性；为满足天线反射器高性能需求，分析了碳纤维种类、纤维体积分数对单胞等效性能的影响规律。对该材料力学性能的研究，可以为其未来应用于大型高精度可展开天线反射器提供一定的理论依据。     

基于激光反射层析法的换能器声场测量技术及仿真研究

换能器的辐射声场分布能够直接反映出换能器声学性能的好坏，若不能精确测量出换能器的辐射声场，则会对换能器的诊断和评估造成严重影响。从理论仿真的角度出发，推导了运用激光反射层析法重建换能器辐射声场的理论公式，着重利用推导出的理论公式对激光反射层析法进行了仿真计算。结果表明激光反射层析法能够精确地重建出换能器的辐射声场分布及声场中的声压量值，这为换能器的声场重建及声压测量提供了一种可行的方法。